Summary
It is not known what loads act on an internal spinal fixation device in patients with a fractured vertebral body. To measure the implant loads in vivo, telemeterized internal spinal fixators were implanted in a patient, and the implant loads measured for numerous body positions and activities before and after anterior fusion. The highest implant loads were found while the patient lifted both extended legs in a supine position. High implant loads were also measured for lateral bending during standing as well as for walking and carrying a load in one hand. The implant loads were small in recumbent positions. In contrast to findings in another patient, who was treated for degenerative instability, implant loads were smaller in the first months after anterior fusion than before. The indication for stabilization and surgical procedure strongly influence implant loads.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Bergmann G, Graichen F, Siraky J, Jendrzinski H, Rohlmann A (1988) Multichannel strain gauge telemetry for orthopaedic implants. J Biomech 21:169–176
Denis F (1983) The three-column spine and its significance in the classification of acute thoracolumbar spinal injuries. Spine 8:817–831
Dick W (1989) Internal fixation of thoracic and lumbar spine fractures. Huber, Berne
Graichen F, Bergmann G, Rohlmann A (1990) Dual 8-channel telemetry system for in vivo load measurements with two instrumented implants. In: Bergmann G, Graichen F, Rohlmann A (eds) Implantable telemetry in orthopaedics. Forschungsvermittlung, Free University, Berlin, pp 153–162
McGill SM (1992) A myoelectrically based dynamic three-dimensional model to predict loads on lumbar spine tissues during lateral bending. J Biomech 25:395–414
Rohlmann A, Bergmann G, Graichen F (1994) A spinal fixation device for in vivo load measurement. J Biomech 27:961–967
Rohlmann A, Bergmann G, Graichen F, Mayer H-M. Telemeterized load measurement using instrumented spinal internal fixators in a patient with degenerative instability. Spine (in press)
Schläpfer F, Magerl F, Jacobs R, Perren SM, Weber BG (1980) In vivo measurements of loads on an external fixation device for human lumbar spine fractures. Inst Mech Eng C 131: 59–64
Schultz AB, Andersson GBJ, Örtengren R, Haderspeck K, Nachemson A (1982) Loads on the lumbar spine. J Bone Joint Surg [Am] 64:713–720
Schultz AB, Andersson GBJ, Haderspeck K, Örtengren R, Nordin M, Björk R (1982) Analysis and measurement of lumbar trunk loads in tasks involving bends and twists. J Biomech 9:669–675
Wiktorin C von H, Nordin M (1986) Introduction to problem solving in biomechanics. Lea & Febiger, Philadelphia
Wilke H-J, Claes L, Wörsdörfer O (1990) In vivo measurements at spinal stabilization implants. Proceedings of the 7th meeting of the European Society of Biomechanics, Aarhus, Denmark, A3
Wörsdörfer O (1981) Operative Stabilisierung der thorakolumbalen und lumbalen Wirbelsäule: vergleichende biomechanische Untersuchungen zur Stabilität und Steifigkeit verschiedener dorsaler Fixationssysteme. Thesis, University of Ulm, Ulm, Germany
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Rohlmann, A., Bergmann, G., Graichen, F. et al. In vivo measurement of implant loads in a patient with a fractured vertebral body. Eur Spine J 4, 347–353 (1995). https://doi.org/10.1007/BF00300295
Received:
Revised:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF00300295